Iranian Journal of Materials Science and Engineering

---

---

---

In this study, CrN/ZrN multilayer nanostructured coatings with different bilayers (10, 20, and 30) were created by the cathodic arc evaporation. The electrochemical behavior of samples was evaluated by polarization and impedance spectroscopy tests in the Ringer medium and the pin on disk test was used to investigate the tribological behavior of the samples. The results of measurements showed that the electrochemical and tribological behavior of the coatings depends on the number of bilayers and by rising the number of bilayers, the coating shows higher corrosion resistance and better tribological performance. Field emission scanning electron microscopy (FE-SEM) images of the specimens after exposure to the corrosion medium showed that the number of surface cavities were formed by the coating that had the highest number of bilayers comparing with other coatings were quite fewer in number and smaller in diameter. The results of the pin on disk test showed that by increasing the number of bilayers from 10 to 30, the coefficient of friction and wear rate decreased and the 30L coating ‌showed better wear resistance.

---

Hybrid composite finds wide application in various fields. In this present study, the hybrid composites are developed using stir casting technique as per Taguchi’s L9 orthogonal array. Hybrid composites were fabricated using Aluminium Al6082 as the base material and reinforced with the combinations of reinforcements Al2SiO5 and B4C at three levels (4%, 8% and 12%).The developed composites were analyzed for micro structural  investigations and mechanical tests were done as per ASTM standards. The micro structural analysis was done using optical Microscope and Scanning electron microscope while composition studies were done using X-ray diffraction and EDAX. Mechanical test like tensile, impact and flexural were conducted and their damage assessment was done using Scanning electron microscope. The fatigue characteristics like high cycle fatigue and fatigue crack propagation was studied both experimentally and numerically. The experimental data and numerical modeling analysis data obtained for the hybrid composite system, agree with each other.           

---

Single crystals of double crystalline block copolymers of poly(ethylene glycol) (PEG)-b-poly(ε-caprolactone) (PCL) and PEG-b-poly(L-lactide) (PLLA) were grown from dilute solution in homo- and mixed-brush systems. Crystallization behavior of biodegradable one end-restricted crystallizable PCL and PLLA chains in homo- and mixed-brush nanostructures were investigated. Chemical and physical circumstances of crystallizable brushes were altered. Physical environment was adjusted by amorphism/crystallinity and rigidity/flexibility of neighboring brushes. Chemical environment was manipulated by interaction and miscibility of various brushes. Distinct single crystals were grown with mixed-brushes of amorphous-crystalline (polystyrene (PS), poly(methyl methacrylate) (PMMA), PCL and PLLA, double crystalline (PCL/PLLA), and rod-crystalline polyaniline (PANI)/PCL or PLLA. Surrounding was only effective on hindrance or nucleation commencement of crystallization for crystallizable brushes and had no effect on crystallization features. Novel three-layer fully single crystalline nanostructures, whose characteristics were fixed via changing the crystallization temperature, were also developed. For long crystallizable tethers, crystallization increased both brush and substrate thicknesses. 

---

Abstract
In this research, Gelatine (GEL)/ Chitosan (CH) wound dressing was prepared and irradiated with gamma rays from ⁶⁰Co source for wound healing applications. GEL-CH composite characterization and functional properties were determined. The structural changes occurring after γ-irradiation at doses from 5 to 25 kGy were reported by physico-chemical techniques such as Electron Paramagnetic Resonance (EPR), Fourier Transform Infrared spectroscopy (FTIR), X-ray diffraction (XRD) and Electrochemical Impedance Spectroscopy (EIS) studies. The antioxidant capacity was studied using DPPH (1,1-diphenyl-2-picrylhydrazyl free radical) scavenging and the antibacterial activities of Staphylococcus aureus and Escherichia coli were observed using liquid medium. Results revealed that EPR spectroscopy of un-irradiated GEL-CH showed 2 paramagnetic centers correspond to g=2.077 and g= 2.079. After irradiation, no active centre was appeared. A dose-dependent decrease in the central signal intensity was detected, then the EPR signal intensity almost disappears at 20 kGy. Gamma rays caused a slight increase in ion conductivity. FTIR suggest a slightly crosslinking phenomenon at 20 kGy. The XRD analysis does not show peak indicating crystallinity between a range of 2θ (15–30°). Moreover, γ-irradiation elevated the Scavenging DPPH radical activity (0.75 ± 0.07%). Gamma rays did not affect the antibacterial activity of GEL-CH wound dressing against pathogenic bacteria. The innovative results showed that the required γ-radiation for sterilization was ranged from 5 to 25 kGy. It permits to improve the physico-chemical and biological properties and maintain the native structural integrity of the GEL/ COL wound dressing

---

Abstract
Gelatin (GEL) is most extensively used in various fields, particularly in therapeutics and pharmaceuticals. GEL was extracted from goat skin using hot temperature extraction process and compared with that of commercial GEL. The physico-chemical characterization and functional properties were investigated by using temperature denaturation (T_d), water-holding and fat-binding capacities (WHC and FBC), colour measurement and UV-light spectrum. In vitro biocompatibility was studied for the first time and was evaluated by blood coagulation index (BCI) and haemolytic tests for using as wounds dressing. The results revealed thermal stability of goat GEL at T_d 37°C. WHC and FBC capacities represented 2.5 and 1.2 g/ml, respectively. The hunter colour spaces a*, b* and L* showed a -0.27, -1.97 and 25.23 values, respectively. UV-Vis absorption spectrum of the goat GEL showed a maximum absorption peak at 280 nm. The in vitro anticoagulant activities of extracting GEL were higher than 70% after incubation for one hour. After being in contact with red blood cells for 1 h, the haemolysis ratio increased from to 0.46 to 1.4 when the concentration of goat GEL increased from 1 to 50 mg/ml suggesting the safety of the tested samples. These results suggest that thromboresistivity and hemocompatibility of this biopolymer retained the biological activity of our samples for biomaterial applications. According to this, goat GEL successfully competes with, and significantly could be useful for substitution of bovine in wound healing.

---

In this study, for the first time, the Forsterite (Mg₂SiO₄) nanoparticles (NPs) with the size of about 25 nm were added to the phosphate-based electrolyte, and the characteristics and properties of the obtained plasma electrolytic oxidation (PEO) coating on AZ31 Mg alloy was investigated. The results of the potentiodynamic polarization measurements revealed that after one week of exposure to simulated body fluid (SBF) solution, the coating with Mg₂SiO₄ NPs possessed 12.30 kΩ cm² polarization resistance, which was more than two times greater than that of the coating without NPs. The thicker coating layer, lower wettability, and also presence of Mg₂SiO₄ NPs inside the pores were responsible for enhanced corrosion protection in the Mg₂SiO₄ NPs incorporated coating. After three weeks of immersion in SBF solution, the in-vitro bioactivity test results indicated the ability of the NPs-containing coating to form apatite (Ca/P ratio of 0.92) was weaker than the coating without NPs (Ca/P ratio of 1.17). This could be attributed to the lower wettability of the coating with NPs and supports that the addition of the nanoparticles is not beneficial to the bioactivity performance of the coating. 

---

     Zinc Oxide (ZnO) nanorods and titanium dioxide (TiO₂) nanostructures thin films were prepared onto glass substrates by the chemical bath deposition (CBD) method. The ZnO was structured as nanorods (NRs) while TiO₂ was formed as nanoflowers plate as confirmed by Field-Emission Scanning Electron Microscope (FESEM) images. The ZnO/Fe₃O₄ and TiO₂/Fe₃O₄ nanostructures thin films were prepared via drop-casting Fe₃O₄ NPs onto the grown ZnO and TiO₂ nanostructures thin films. The diameter of Fe₃O₄ NPs was deposited onto ZnO NRs thin films and TiO₂ nanostructures thin films was ranged from 8nm to 59nm with dominated range between 10nm to 30 nm.  The crystalline structure of prepared samples was investigated through X-ray diffraction (XRD) method. However, the particles size of Fe₃O₄  was estimated  by XRD as well as FESEM images was around 22 nm. The photocatalytic activity of the as-prepared ZnO/Fe₃O₄ and TiO₂/Fe₃O₄ nanostructures thin films was investigated against methylene blue (MB) dye at room temperature with a pH value of 10 under different exposure time by visible light. The photodegradation rate of MB dye by ZnO/Fe₃O₄ and TiO₂/Fe₃O₄ nanostructures thin films was higher than that obtained by ZnO and TiO₂ nanostructures thin films. The best photodegradation rate of MB dye was 100% after exposure time of 180 min was obtained by ZnO/Fe₃O₄ nanostructures thin film whereas it was 82% for TiO₂/Fe₃O₄ nanostructures thin films after exposure time of  240 min.  
 

---

This paper aims to study the tribological and electrochemical properties of the CrN/AlCrN nano-layer deposited on H13 tool steel. Arc physical technique was employed to deposit multilayer coating. X-ray diffraction technique, thermionic and field emission scanning electron microscopy and energy dispersive spectroscopy have been used to determine the characteristics of the samples. To study the samples' wear behavior, coating adhesion, and surface hardness, reciprocating wear test, Rockwell-C test, and microhardness Vickers tester were employed, respectively. The measured values of the coefficient of friction and the calculated wear rates showed that the CrN/AlCrN multilayer coating has a much higher wear resistance than the uncoated sample. The coefficient of the friction of the coated sample was 0.53 and that of the uncoated sample was 0.78. Moreover, the wear rate of the coated H13 steel was about 127 times lower than the bare H13 steel sample. The results obtained from electrochemical impedance spectroscopy and polarization tests demonstrated that the corrosion current density of the H13 steel sample was 8 μA/cm2 and that of the CrN/AlCrN multilayer-coated sample was 3 μA/cm2. In addition, the polarization resistance of the treated and the substrate specimens was estimated at 4.2 and 2.7 kΩ.cm2, respectively.

---

As a major global cause of liver disease, non-alcoholic fatty liver disease (NAFLD) is characterized by excessive hepatocellular accumulation of lipids in the liver, elevated levels of hepatic enzymes, and fibrotic evidence. The primary therapies for NAFLD are changing lifestyle or managing comorbid-associated diseases. Lately, nanotechnology has revolutionized the art of nanostructure synthesis for disease imaging, diagnosis, and treatment. Loading drugs into nanocarriers has been established as a promising strategy to extend their circulating time, particularly in treating NAFLD. In addition, considering a master modulator of adipogenesis and lysosomal biogenesis and function, designing novel nanostructures for biomedical applications requires using biodegradable materials. Various nanostructures, including inorganic nanoparticles (NPs), organic-based NPs, metallic nanocarriers, biodegradable polymeric nanocarriers, polymer-hybrid nanocarriers, and lipid-based nanocarriers have been designed for NAFLD treatment, which significantly affected serum glucose/lipid levels and liver function indices. NPs modified with polymers, bimetallic NPs, and superparamagnetic NPs have been used to design sensitive nanosensors to measure NAFLD-related biomarkers. However, certain limitations are associated with their use as diagnostic agents. The purpose of this review article is to shed light on the recent advancements in the field of nanomedicine for the early diagnosis, treatment, and prognosis of this progressive liver disease.
 

---

Considering the widespread use of aluminum composites in various industries and the emergence of nanomaterials such as graphene and boron nitrite (BN) with their unique properties, aluminum-based nanocomposite reinforced by the graphene-BN hybrid was fabricated at different percentages. For this purpose, the graphene-BN hybrid was prepared and subjected to wet milling along with the aluminum powder. The mechanical properties of the final nanocomposite which was consolidated using the spark plasma sintering (SPS) method were examined. Aluminum-based composite specimens containing 1 wt.% graphene–0 wt.% BN (AGB1), 0.95 wt.% graphene–0.05 wt.% BN (AGB2), 0.90 wt.% graphene–0.1 wt.% BN (AGB3), and 0.85 wt.% graphene–0.15 wt.% BN (AGB4) were fabricated and compared with non-reinforced aluminum (AGB0). The hardness values of 48.1, 51.1, 56.2, 54.1, and 43.6 Hv were obtained for AGB0, AGB1, AGB2, AGB3, and AGB4, respectively. Additionally, tensile strengths of these specimens were 67.2, 102.1, 129.5, 123.7, and 114.7 MPa, respectively. According to the results of the hardness and tensile tests, it was revealed that the AGB2 specimen had the highest tensile strength (93% higher than AGB0 and 27% higher than AGB1) and hardness (17% higher than AGB0 and 10% higher than AGB1).

---

This contribution evaluates the influence of Cr doping on the ground state properties of SrTiO3 Perovskite using GGA-PBE approximation. Results of the simulated model infer agreement with the previously published literature. The modification of electronic structure and optical properties due to Cr3+ doping levels in SrTiO3 has been investigated. Structural parameters infer that Cr3+ doping alters the electronic structures of SrTiO3 by shifting the conduction band through lower energies for the Sr and Ti sites. Substituting Ti site by Cr3+ results the energy gap in being eliminated revealing a new electrical case of conducting material for the system. Furthermore, it has been noticed that Cr doping either at Sr or Ti positions could effectively develop the SrTiO3 dielectric constant properties. Consequently, Cr3+ is an effective dopant due to enhancing the optical absorption properties, thus opening up new prospects for optoelectronic applications.

---

Novelty: Most of the open literature research has focused on the microstructural evolution and mechanical properties of AA2050 alloy. Also, a significant study discusses the corrosion behavior of AA2050 alloy based on immersion and electrochemical characteristics. The influence of heat treatment on the microstructure and mechanical properties of friction stir processed AA2050 alloy is scarcely discussed in the open literature. The hot salt corrosion characteristics of friction stir processed AA2050 seldom exists in the available literature. This study concentrates on microhardness, tensile strength, and corrosion properties of friction stir processed AA2050. Also, the work focuses on the influence of artificial aging on the microhardness, and tensile strength of the friction stir processed AA2050.

 

---

In this study, an epoxy-based nanocomposite reinforced with copper oxide-graphene oxide hybrid was investigated. Initially, the hybrid powder of CuO–GO with a weight ratio of 9:1 was prepared. The hybrid filler with different weight percentages ranging from 0.1–0.5 was used to reinforce the epoxy resin. The prepared samples were analyzed using XRD, FTIR, FESEM, TEM, and tensile testing. According to the XRD results and SEM images, the hybrid powder was successfully prepared, and the mechanical testing results showed an improvement in tensile strength in the composite samples. The best composite sample in terms of tensile strength was the one containing 0.3 wt% of hybrid reinforcement, which exhibited a 73% increase in strength compared to the neat resin sample.

---

The present work deals with the effect of Multi-walled Carbon Nanotube (MWCNT) and functionalized (carboxyl and amine) MWCNT on the mechanical properties of the PAEK (Poly Aryl Ether Ketone) polymer composite. The MWCNT and functionalized (carboxyl and amine) MWCNT concentration varied as 0.25, 0.5 and 0.75 weight percentages. Compositeswere prepared by using a melt compounding method using a twin-screw extruder and all testing samples were prepared using an injection molding machine as per American Society for Testing and Materials (ASTM) standards. Samples were tested for tensile strength, impact strength, flexural strength, heat deflection temperature, hardness, and density. There is an increase in the tensile strength, impact strength, flexural strength, and heat deflection temperature, with percentage increase in filler loading up to 0.5 %, followed by decrease in it with higher filler loading. The increase is maximum for amine functionalized MWCNT.

 

---

In this research work, Cadmium Sulphide thin film deposited on to glass substrate in a non-aqueous medium at 80 °C. The various physical preparative parameters and the deposition conditions, such as the deposition time and temperature, concentrations of the chemical species, pH, speed of mechanical stirring, etc., were optimized to yield good quality films. The as-prepared sample is tightly adherent to the substrate's support, less smooth, diffusely reflecting and was analyzed for composition. The synthesized film is characterized using X- ray diffraction (XRD), electrical and optical properties. It appears that the composites are rich in Cd. The grown CdS thin film had an orange-red color. A band gap of CdS thin film is 2.41 eV.  The average crystallite size of the CdS film was 21.50 nm. The resistivity of the CdS thin film is about 5.212 x 10⁵ W cm.
 

---

The present investigation delves into the friction stir welding of AA5052 and AZ31B alloys, examining the effects of three distinct parameter configurations. A face-centered central composite design, structured to incorporate full replications for comprehensive and reliable analysis, was employed. A pivotal element of this study is implementing an advanced deep neural network (DNN) model. Characterized by its varied activation functions, structural parameters, and training algorithms, this DNN model was adeptly configured to precisely predict the tensile strength and microhardness of the welded joints. This comprehensive examination also included a quantitative assessment of the parameter effects on joint microstructure and mechanical properties. Flawless welds with exemplary surface characteristics were attained through a meticulously optimized set of parameters: a tool rotation speed set at 825 rpm, a tool traverse speed of 15 mm/min, and a shoulder diameter of 18 mm. During the welding process, the formation of intermetallic compounds, specifically Al₁₂Mg₁₇ and Al₃Mg₂, was observed. An exceptionally refined grain size of 2.23 µm was observed in the stir zone, contributing to the joint's enhanced tensile strength, measured at 180 MPa. The hardness of the specimen fabricated at the high rotational speed is more elevated due to the brittle intermetallic compounds. The better mechanical properties are related to the reduction and distribution of intermetallic compounds formed in the interface zone.  

---

Biogenic synthesis of papain-conjugated copper metallic Nanoparticles and their antibacterial and antifungal activities Papain metallic conjugated nanoparticles (Papain-CuNPs) were synthesised using Papain and CuSO4.5H₂O. Papain-CuNPs were characterized using UV-visible spectroscopy, FT-IR, HR-TEM, XRD, FE-SEM, zeta potential, and a zeta sizer. The antibacterial activity of papain-CuNPs against human infectious microorganisms (Citrobacter spp, Pseudomonas aeruginosa and Candida albicans) was investigated. The mechanism of action of papain-CuNPs was evaluated using FE-SEM and HRTM. UV spectroscopy confirmed the plasma resonance (SPR) at 679 nm, which indicated the formation of papain-CuNPs. The FT-IR spectrum absorbance peaks at 3927, 3865, 3842, 3363, 2978, and 2900 cm^-1 indicate the presence of O-H and N-H of the secondary amine, and peaks at 1643 and 1572 cm^-1 represent C=O functional groups in Papain-CuNPs. EDAX analysis confirmed the presence of copper in the papain-CuNPs. The zeta potential (-42.6 mV) and zeta size (99.66 d. nm) confirmed the stability and size of the nanoparticles. XRD confirmed the crystalline nature of the papain-CuNPs. FE-SEM and HRTM showed an oval structure, and the nano particles' 16.71244–34.84793 nm. The synthesized papain-NPs showed significant antibacterial activity against clinical P. aeruginosa (15 mm). MIC 125 µg/ml) showed bactericidal activity against P. aeruginosa and the mechanism of action of Papain-NPs was confirmed using an electron microscope by observing cell damage and cell shrinking. Papain-CuNPs have significant antibacterial activity and are thus used in the treatment of P. aeruginosa infections

---

Despite being an effective material for food packaging, chitosan (CS) exhibited poor ductility when processed into film, which restricted its use in this industry. In this study, composite films with enhanced properties were developed by incorporating polyvinyl alcohol (PVA) into CS through a simple solution casting method. The effects of different PVA/CS weight ratios (70:30, 50:50, and 30:70 w/w) on the morphology, mechanical properties, antibacterial activity, and soil degradation of the composite films were analyzed. Compared to the pristine PVA film, increasing the CS content in the PVA/CS composite film enhanced thickness, stiffness, roughness, antibacterial efficiency, and degradation rate, while reducing tensile strength and elongation at break. Fourier transform infrared (FTIR) spectroscopy revealed the highest intermolecular interactions in the PVA/CS composite film with 70:30 w/w. Antibacterial activity tests and soil burial analysis demonstrated that the PVA:70/CS:30 composite exhibited significantly higher antibacterial activity toward Escherichia coli and Bacillus subtilis bacteria as opposed to PVA film, along with a moderate degradation rate of 76.76% following 30 days soil burial, effectively balancing biodegradability and material integrity. These findings suggest that the PVA:70/CS:30 composite is a promising alternative for sustainable and functional biodegradable packaging solutions.